Raskullz Helmets, Burgundy

Age 3-5. Shock absorbing EPS inner shell. Molded 3D helmet design. Adjustable Straps. Aerodynamic cooling vents. 48-52 cm. Protection and Ventilation: The outer shell allows the helmet to be one of me lightest helmets while providing excellent durability and integrity. The multiple vents with inner air channels draw the air throughout the helmet and over the brow for maximum cooling Fitting: The helmet is designed to be retained by a strap under the lower jaw. To be effective, a helmet must fit and be worn correctly. To check for correct fit, place helmet on the head and make any adjustment indicated. Securely fasten retention system. Grasp the helmet and try to rotate it to the front and rear. A correctly fitted helmet should be comfortable and should not move forward to obscure vision or rearward to expose the forehead. To ensure a proper fit, mix and match the pad thickness to best conform to your head shape. Retention System: This helmet uses a retention system that is simple and can be buckled and unbuckled without changing the adjustment. The straps must be snug and evenly tensioned. The helmet is designed to be retained by a strap under the lower jaw. Place helmet firmly on your head and fasten the buckle. To tighten the rear strap, pull excess from the rear of Strap (2) Hold the helmet with one hand. With the other hand, hold the strap where they pass under your chin. Then pull from side to side to balance the length of all your straps. The helmet must sit firmly and level on your head. To lower the front of the helmet in order to cover your forehead, tighten the chin strap and loosen the rear strap. To raise front, loosen the chin strap and tighten the rear strap. Final Check: The important thing to remember is that the helmet must fit snugly. If you can tilt it forwards or backwards, you will need to tighten the strap adjustment. It is important for the helmet to fit snug on your head and be properly fastened to provide maximum protection. All adjustments should be checked each time the helmet is worn, making sure it fits snug each time. Complies with U.S. CPSC safety standard for bicycle helmets for persons age 1 and older. (extended head coverage) meets ASTM f1492-08 standard. Safety Information: If your helmet bears the CPSC designation, it meets the CPSC 1203: Safety standard for bicycle helmets requirements of the consumer product safety commission. If your helmet bears the ASTM designation, it meets the ASTM F1492: Standard for Helmet used in skateboarding and trick roller skating requirements of the American society of testing and materials. If your helmet bears the AS/NZS designation, it meets the AS/NZS 2063 safety requirement, of the council of standards Australia and the council of standards New Zealand. If your helmet bears the CE designation, it meets the EN 1078 safety requirements of the European committee for standardization. Raskullz.com. Made in China. Color: Burgundy

Age 3-5. Shock absorbing EPS inner shell. Molded 3D helmet design. Adjustable Straps. Aerodynamic cooling vents. 48-52 cm. Protection and Ventilation: The outer shell allows the helmet to be one of me lightest helmets while providing excellent durability and integrity. The multiple vents with inner air channels draw the air throughout the helmet and over the brow for maximum cooling Fitting: The helmet is designed to be retained by a strap under the lower jaw. To be effective, a helmet must fit and be worn correctly. To check for correct fit, place helmet on the head and make any adjustment indicated. Securely fasten retention system. Grasp the helmet and try to rotate it to the front and rear. A correctly fitted helmet should be comfortable and should not move forward to obscure vision or rearward to expose the forehead. To ensure a proper fit, mix and match the pad thickness to best conform to your head shape. Retention System: This helmet uses a retention system that is simple and can be buckled and unbuckled without changing the adjustment. The straps must be snug and evenly tensioned. The helmet is designed to be retained by a strap under the lower jaw. Place helmet firmly on your head and fasten the buckle. To tighten the rear strap, pull excess from the rear of Strap (2) Hold the helmet with one hand. With the other hand, hold the strap where they pass under your chin. Then pull from side to side to balance the length of all your straps. The helmet must sit firmly and level on your head. To lower the front of the helmet in order to cover your forehead, tighten the chin strap and loosen the rear strap. To raise front, loosen the chin strap and tighten the rear strap. Final Check: The important thing to remember is that the helmet must fit snugly. If you can tilt it forwards or backwards, you will need to tighten the strap adjustment. It is important for the helmet to fit snug on your head and be properly fastened to provide maximum protection. All adjustments should be checked each time the helmet is worn, making sure it fits snug each time. Complies with U.S. CPSC safety standard for bicycle helmets for persons age 1 and older. (extended head coverage) meets ASTM f1492-08 standard. Safety Information: If your helmet bears the CPSC designation, it meets the CPSC 1203: Safety standard for bicycle helmets requirements of the consumer product safety commission. If your helmet bears the ASTM designation, it meets the ASTM F1492: Standard for Helmet used in skateboarding and trick roller skating requirements of the American society of testing and materials. If your helmet bears the AS/NZS designation, it meets the AS/NZS 2063 safety requirement, of the council of standards Australia and the council of standards New Zealand. If your helmet bears the CE designation, it meets the EN 1078 safety requirements of the European committee for standardization. Raskullz.com. Made in China. Color: Burgundy

Usage of instructions:instructions for use: designed for the use recycling, skateboarding or roller stating and is not designed for motorcycle use. this helmet cannot protect against all types of helmet is designed to absorb shock by partial instruction of the energy absorbing liner. this damage may not be visible. therefore, if subjected to a severe blow, the helmet should be destroyed and replaced even if it appears damaged. no attachments should be made to the helmet except those recommended by the helmet manufacture design of this helmet id not to withstand multiple facts. clean with mild soap and water only, do not use any solvents as this will damages the helmet and do not dry in. pay attention to sharp objects and the helmet in direct sunlight. this helmet has a limited lifespan in use and should be replaced when it shows of wear. this helmet should not be used be build while climbing or doing other activates where there is a risk of hanging or strangulation if the child gets strapped the helmet. please read enclosed manual using your new helmet. - directions: instructions for use: designed for the use recycling, skateboarding or roller stating and is not designed for motorcycle use. this helmet cannot protect against all types of helmet is designed to absorb shock by partial instruction of the energy absorbing liner. this damage may not be visible. therefore, if subjected to a severe blow, the helmet should be destroyed and replaced even if it appears damaged. no attachments should be made to the helmet except those recommended by the helmet manufacture design of this helmet id not to withstand multiple facts. clean with mild soap and water only, do not use any solvents as this will damages the helmet and do not dry in. pay attention to sharp objects and the helmet in direct sunlight. this helmet has a limited lifespan in use and should be replaced when it shows of wear. this helmet should not be used be build while climbing or doing other activates where there is a risk of hanging or strangulation if the child gets strapped the helmet. please read enclosed manual using your new helmet. for maximum protection the helmet must be fitted and attached properly to the wearer's head in accordance with the manufacturer's fitting instructions. this helmet is intended only for pedal cyclists, skateboarder or rollerskaters, as specified on the label inside of helmet. it is not intended for motorsport, moped or other similar uses. fitting instructions: (1) helmet size: choose a helmet size that is comfortable yet snug on your child's head. comfortable fitting pads are provided to help achieve a custom fit. (2) adjusting straps: place helmet level on head with straps junction forming a y under ears. tighten all straps evenly and buckle under chin. secure loose end strap with rubber o-ring provided. straps should be tight enough to prevent from shifting forward or backward when moved by hand. shift the helmet around back and forth, and side to side. helmet should remain comfortable yet move the skin of the brow with it. caring for your helmet: it is recommended you clean your helmet with mild soap and water, and with a soft cloth or sponge. the helmet may be damaged and rendered ineffective by petroleum and petroleum products such as cleaning agents, paints, adhesives and the like, without the damage being visible to the user. c-preme also recommends that helmets be replaced every 3-5 years from the data of purchase. keep helmets out of extreme heat. excessive he can damage the helmet. in direct sun light, car interiors and reflective surfaces can heat a helmet enough to cause damage damaged helmets will appear to have uneven or bubbly surfaces, or show other evidence of distortion. if damaged, helmets should be destroyed and replaced immediately.

Usage of instructions:instructions for use: designed for the use recycling, skateboarding or roller stating and is not designed for motorcycle use. this helmet cannot protect against all types of helmet is designed to absorb shock by partial instruction of the energy absorbing liner. this damage may not be visible. therefore, if subjected to a severe blow, the helmet should be destroyed and replaced even if it appears damaged. no attachments should be made to the helmet except those recommended by the helmet manufacture design of this helmet id not to withstand multiple facts. clean with mild soap and water only, do not use any solvents as this will damages the helmet and do not dry in. pay attention to sharp objects and the helmet in direct sunlight. this helmet has a limited lifespan in use and should be replaced when it shows of wear. this helmet should not be used be build while climbing or doing other activates where there is a risk of hanging or strangulation if the child gets strapped the helmet. please read enclosed manual using your new helmet. - directions: instructions for use: designed for the use recycling, skateboarding or roller stating and is not designed for motorcycle use. this helmet cannot protect against all types of helmet is designed to absorb shock by partial instruction of the energy absorbing liner. this damage may not be visible. therefore, if subjected to a severe blow, the helmet should be destroyed and replaced even if it appears damaged. no attachments should be made to the helmet except those recommended by the helmet manufacture design of this helmet id not to withstand multiple facts. clean with mild soap and water only, do not use any solvents as this will damages the helmet and do not dry in. pay attention to sharp objects and the helmet in direct sunlight. this helmet has a limited lifespan in use and should be replaced when it shows of wear. this helmet should not be used be build while climbing or doing other activates where there is a risk of hanging or strangulation if the child gets strapped the helmet. please read enclosed manual using your new helmet. for maximum protection the helmet must be fitted and attached properly to the wearer's head in accordance with the manufacturer's fitting instructions. this helmet is intended only for pedal cyclists, skateboarder or rollerskaters, as specified on the label inside of helmet. it is not intended for motorsport, moped or other similar uses. fitting instructions: (1) helmet size: choose a helmet size that is comfortable yet snug on your child's head. comfortable fitting pads are provided to help achieve a custom fit. (2) adjusting straps: place helmet level on head with straps junction forming a y under ears. tighten all straps evenly and buckle under chin. secure loose end strap with rubber o-ring provided. straps should be tight enough to prevent from shifting forward or backward when moved by hand. shift the helmet around back and forth, and side to side. helmet should remain comfortable yet move the skin of the brow with it. caring for your helmet: it is recommended you clean your helmet with mild soap and water, and with a soft cloth or sponge. the helmet may be damaged and rendered ineffective by petroleum and petroleum products such as cleaning agents, paints, adhesives and the like, without the damage being visible to the user. c-preme also recommends that helmets be replaced every 3-5 years from the data of purchase. keep helmets out of extreme heat. excessive he can damage the helmet. in direct sun light, car interiors and reflective surfaces can heat a helmet enough to cause damage damaged helmets will appear to have uneven or bubbly surfaces, or show other evidence of distortion. if damaged, helmets should be destroyed and replaced immediately.