Avalanche Black Diamond Refrigerant (12 oz)

New EPA self-sealing valve. No. 1 super chill formula. Ultra synthetic. Maximum cooling. Stops leaks. Extends system life. Black Diamond Avalanche contains 11 oz. of R-134a and 1 oz. of no. 1 super chill formula to ensure maximum cold air while sealing common rubber o-rings, gasket, and hose leaks and extending compressor life. www.acavalanche.com. Scan to visit our website and to view our how to video. Facebook: Like us. Youtube: Watch us. For more information visit www.acavalanche.com. Assembled in the USA from components of USA and China. Tsi Products,

New EPA self-sealing valve. No. 1 super chill formula. Ultra synthetic. Maximum cooling. Stops leaks. Extends system life. Black Diamond Avalanche contains 11 oz. of R-134a and 1 oz. of no. 1 super chill formula to ensure maximum cold air while sealing common rubber o-rings, gasket, and hose leaks and extending compressor life. www.acavalanche.com. Scan to visit our website and to view our how to video. Facebook: Like us. Youtube: Watch us. For more information visit www.acavalanche.com. Assembled in the USA from components of USA and China. Tsi Products,

Directions: Installation Instructions: 1. Locate the vehicle's low side service port. This port will often have a plastic cap and is located between the a/c compressor and the evaporator. It is the only port to which a R-134a recharge hose will connect. This is a self-sealing can and requires a recharge hose made for self-sealing cans. We recommend the Avalanche part (hashtag)AVL402CS Recharge Hose with Smart Clips for correct fill. Always follow the instructions from the device to properly charge. 2. Start the engine and turn air conditioner to maximum cool and maximum air flow. Close passenger compartment. 3. Tighten the recharge hose to the top of the Avalanche can by turning it clockwise. Make sure it is firmly attached. Shake can well. Connect the quick connect coupler on the other end of the hose to the low side service port by pulling the connector ring back as you push the fitting onto the service port. Make sure it locks into place. Do not overcharge / do not vent. Never place refrigerant can on any hot engine part. 4. Following the instructions on your recharge device, add refrigerant while fully rotating the can from a 12 o'clock position to 3 o'clock position. If your system is very low in refrigerant this process can take several minutes. Check vent temperature often while increasing your RPM slightly. The word Avalanche will turn to blue indicating refrigerant is being added to your system. 5. When you have the correct fill and your air conditioner is blowing cold, re-seal the can per the instructions on your charging device. Remove the quick connect coupler from the vehicle's service port. If can is not empty, keep hose on and store can in a cool dry place. When empty, the hose may be detached and re-used, discard the can according to state or local guidelines.

Directions: Installation Instructions: 1. Locate the vehicle's low side service port. This port will often have a plastic cap and is located between the a/c compressor and the evaporator. It is the only port to which a R-134a recharge hose will connect. This is a self-sealing can and requires a recharge hose made for self-sealing cans. We recommend the Avalanche part (hashtag)AVL402CS Recharge Hose with Smart Clips for correct fill. Always follow the instructions from the device to properly charge. 2. Start the engine and turn air conditioner to maximum cool and maximum air flow. Close passenger compartment. 3. Tighten the recharge hose to the top of the Avalanche can by turning it clockwise. Make sure it is firmly attached. Shake can well. Connect the quick connect coupler on the other end of the hose to the low side service port by pulling the connector ring back as you push the fitting onto the service port. Make sure it locks into place. Do not overcharge / do not vent. Never place refrigerant can on any hot engine part. 4. Following the instructions on your recharge device, add refrigerant while fully rotating the can from a 12 o'clock position to 3 o'clock position. If your system is very low in refrigerant this process can take several minutes. Check vent temperature often while increasing your RPM slightly. The word Avalanche will turn to blue indicating refrigerant is being added to your system. 5. When you have the correct fill and your air conditioner is blowing cold, re-seal the can per the instructions on your charging device. Remove the quick connect coupler from the vehicle's service port. If can is not empty, keep hose on and store can in a cool dry place. When empty, the hose may be detached and re-used, discard the can according to state or local guidelines.